SMED (Single Minute Exchange of Die) has traditionally been misunderstood as a simple workshop dynamic or a generic "Lean" housekeeping tool. In high-level engineering, this conception is inadequate. From the Cronometras perspective, SMED is a mathematical and biomechanical challenge: it is the systematic reduction of TMUs (Time Measurement Units) and the elimination of stochastic variability in the changeover process. We are not simply trying to "go faster"; we seek to alter the physics of the method in order to directly impact the Availability component of OEE (Overall Equipment Effectiveness).
Technical Anatomy of Changeover Time in Industry 4.0
To manage technical productivity, we must start from a rigorous definition. Changeover time is not simply "the time the machine is stopped." According to operational excellence standards and current technical regulations, a format changeover is defined as the time interval between the production of the last good part of batch A at nominal speed and the first good part of batch B at nominal speed.
The Availability Problem
As a guideline example, a large share of OEE losses in high-cadence sectors (metalworking and injection molding) comes from non-standardized changeover times and microstops associated with start-up. A plant with 90 minutes format changeovers and a high frequency of short batches is mathematically unable to compete on cost.
Critical Differentiation of Times
For a time study analyst, segregation is vital:
- IED (Internal Exchange of Die): Operations that can physically only be carried out with the machine stopped. They represent the direct bottleneck and the net loss of capacity.
- OED (External Exchange of Die): Operations that can be carried out with the machine running (masked time). The common mistake is to treat OED as "free time," when in fact it must be timed and optimized with the same rigor as the machine cycle.
Why Traditional Time Studies Fail in SMED
The classic approach of hundredth-of-a-second time study (flyback or cumulative) is usually insufficient for a high-performance SMED project.
- Limitations of the Stopwatch: Measuring the overall time of an operation (e.g., "Change mold") does not reveal micromotion inefficiency. The stopwatch tells us how long it takes, but not why. It does not distinguish between an efficient "Reach" (R) motion and one involving hesitation or searching.
- The "Adjustment" Trap: At Cronometras we have detected that up to 40% of changeover time is lost in "adjustments." The lack of engineering in the tooling turns the changeover into a trial-and-error process. An adjustment is not a method; it is the absence of a standard. If the operator needs to "tweak" the parameters until the part comes out right, the process does not have a stable (Capability Index).
- Effort Factor and Fatigue (ILO): Format changeovers usually involve peaks of physical load (handling loads >15kg, awkward postures). A time study that does not correctly apply the Rest Allowances under ILO regulations will result in an unattainable and dangerous standard time, violating the sustainability of the method.
Advanced Methodology: Integration of MTM and MOST in SMED
This is where methods engineering makes the difference. We elevate SMED from empirical observation to an exact science through predetermined time systems.
From the Stopwatch to MTM-2 / UAS
The use of systems such as MTM-2 (Methods-Time Measurement) or Basic MOST makes it possible to break the changeover operation down into basic motions.
- Technical Case: Replacing a long-threaded screw with a quarter-turn system is not just about "saving time." In MTM terms, we are eliminating multiple "Turn" action codes (which consume high TMUs) and replacing them with a simple "Position and Apply Pressure." This granularity allows us to predict the time saving before making the physical investment in the tooling.
Video Analysis and Two-Hand Charts
We use advanced video analysis software (video analysis) to:
- Segregate IED/OED with frame-level precision.
- Generate Two-Hand Charts: Efficient SMED requires the simultaneous and symmetrical use of both hands, balancing the workload and reducing manual cycle time.
Scientific Standardization
The ILO premise is clear: "Without a standard method, there is no standard time." Our goal is to stabilize the standard deviation ($\sigma$) of the changeover process. Only when the method is robust (clear technical instructions, visual markings, poka-yoke tooling) can we certify a standard time for the ERP.
The 2025 Horizon: Regulations, Ergonomics and Digitalization
Modern methods engineering does not operate in a vacuum. SMED must be aligned with the 2025 regulatory and technological framework.
Compliance with UNE-EN ISO 11228
Time reduction must not compromise occupational health. The SMED analysis must include a biomechanical assessment (NIOSH Equation or OCRA Method) for manual handling of loads.
- Technical Solution: Implementation of hydraulic or magnetic quick clamping systems (Zero-point clamping). This eliminates manual tightening torque, reducing fatigue and ensuring compliance with ISO 11228, while drastically reducing IED.
Energy Efficiency (ISO 50001)
Changeover time is a "phantom consumer." An injection molding machine or a furnace held at operating temperature for 90 minutes of changeover consumes energy without producing value. Reducing SMED is therefore a direct industrial Energy Efficiency action.
From Paper to OTS (One Touch Setup)
The trend toward 2025 is full digitalization. The ultimate goal is OTS: changeovers executed with minimal human intervention, guided by MES (Manufacturing Execution Systems) systems. SOPs (Standard Operating Procedures) must leave paper behind and be integrated into tablets or augmented reality, guiding the operator step by step and validating each stage in real time.
Cronometras Solution: SMED Methods and Time Study Audit
At Cronometras, we turn idle time into productive capacity. We do not run group dynamics; we do engineering. Our intervention is structured in three technical phases:
- MTM Diagnosis: Exact quantification of manual workload and detection of waste invisible to the stopwatch.
- Tooling Engineering: Concrete technical proposals to convert internal operations into external ones and eliminate adjustments (conversion to single-touch).
- Time Study Certification: Delivery of new standards validated under ILO regulations, ready to be loaded into your planning system (ERP/MES) and used for cost calculation.
Is your OEE suffering from low availability and non-standardized changeovers? Stop guessing and start measuring with scientific precision.
👉 [Request a Technical SMED Audit with MTM Specialists]
Technical FAQ (Frequently Asked Questions)
What is the technical difference between SMED and OTS? SMED (Single Minute Exchange of Die) is the methodology for reducing changeover time to less than 10 minutes (a single digit). OTS (One Touch Setup) is the final evolution of SMED, where the changeover is performed with a single motion or button, generally in less than 100 seconds, involving a high degree of automation and digitalization.
How does the MTM system influence changeover time reduction? MTM makes it possible to analyze the method before it occurs. By assigning predetermined time values to human motions, we can design the ideal changeover procedure on paper, eliminating unnecessary motions and calculating the optimal time (Standard Time) without depending on the skill or speed of the current operator.
What do the regulations say about ergonomics in mold changes? The UNE-EN ISO 11228 standard sets limits for the manual lifting and carrying of loads, as well as for the frequency of repetitive motions. In a technical SMED project, it is mandatory to validate that accelerating the process does not force the operator to exceed these biomechanical limits, prioritizing the use of mechanical aids for the phases of greatest effort.
Don't want to do it yourself? We do it for you from €800
If you prefer to outsource it, Cronometras delivers a complete time and motion study from a single video: elemental breakdown, OIT/TAL fatigue allowances, standard time with tolerances, and a report in PDF + Excel + JSON ready to present to management.